What type of spray paint should i use to paint my bmx bike? - bmx paint
I have a bike that I am fit and the bike paint.I removed and the sand below, but you do not know what kind of spray paint, the bike would be better to see
Sunday, November 15, 2009
Bmx Paint What Type Of Spray Paint Should I Use To Paint My Bmx Bike?
Subscribe to:
Post Comments (Atom)
1 comments:
Paintings by bike or take a little more than a whim, a pack of 6, and a weekend. Do it right and it will look good, do evil and I wish you never.
This answer is long, but gives you an idea of what to do. You want a quick answer? Take your bike to a body shop and they do have. It will cost about $ 100 if you take the bike apart.
The use of brand names in auto parts stores DupliColor LACA. In the UK, if you know the brand exists, you need to find a brand of acrylic paint. DO NOT BUY enamel or urethane!
You can have 1 large gray primer can be sanded, the basecoat 1 (if the color does not need much ... ... Read the check box), 1 large can or 2 small cans of paint you want, and 2 or 3 large doses of clearcoat.
Here is a brief explanation, is what to do ...
1) After the complete dismantling of the wheel, you have sanded to remove all of the lens. If the frame is made of aluminum outside, he criticized the mother, or may be chemically peeling paint. Make sure that all color OFFthe bicycle.
2) Read the instructions could be as soon as possible with the first gray spray paint be sanded. Paint Brand DupliColor paint, I think, and you can get your accessories business. Do not buy big boxes, small. Apply at least 1 can be fully realized, in shifts of 15 minutes. Not about the light is now running to worry about.
3) Wait at least 48 hours. There is a difference between painting and paint dry cured ... that must be overcome. First use of 220 grain sandpaper to aluminum oxide (white) or wet / dry paper (black) until the surface is smooth. You should not take long if you have a lot of running.
4) By a tack cloth, lightly not rub on the entire frame (go!) In order to remove the sanding dust.
5) You may be wearing several layers (3 or) the basic color (if necessary 4), then the color of your choice. Make sure the picture is completely covered, it is not necessary that the paint is thick. Follow the instructions on the box. Here, too, paint using the same mark as for priming. Apply a layer 1 / 2 hoursParty. Be sure to cover all parties and not executed. If you go ask too much.
5a) If you want, stickers, wait at least 8 hours, for the decals, then continue. Make sure that the new color as possible to ensure that no watermark or "sticky" in the frame. If you do not add stickers, immediately after the next step within 24 hours ...
6) Do not sand the paint. A layer of clear coat, about 2 boxes full of dollars, coats 15 minutes. If you are clear on stickers, aerosols, at least 4 doses.
7) Allow the frame alone until you do not paint the feeling when you get up close and a breath. If you can not smell, dry! This process takes 2 to 3 days at least.
8) CAREFULLY wet sand the entire frame, with 800 grains of silicon carbide wet or dry paper (black) and 1000 grain silicon carbide wet or dry. Be sure to keep the paper damp cloth to wipe the mud and I know that clean manner. When you begin to see,the color of the joints, STOP! It is difficult to sand and reach the layers of paint. Repeat steps 5, 6 a.m. to 7 p.m., then try again. Do not attempt to fine-tune the environment, it is terrible.
9) Using white paste polishing agent, follow the instructions and polishing the entire frame.
10) DO NOT wax or wash for at least 10 days.
When you finish it with a sloppy throw chaos and try to blow forever. However, if you do your time and things will feel very cool.
Post a Comment